Semi Truck Brake Drum Puller

April 30, 2021

Choose hub socket rock/eat5 cr1798 stem/cr1643/ford fruehauf pro par euclid rock/eat4 choose pulling chains steel alum. Jaws slide for easy placement and held by spring clips.

Pin on Trucks

It has a usable spread of 17.5 inches and a maximum reach of 12.25 inches.

Semi truck brake drum puller. Get yours online today and pick up in store. Thus, my drums are seized. Can be used with air tools to reduce time and fatigue.

One person can easily set the tool in place and use for tough pulls even where there is little access to insert the jaws. My truck came from a snow / salt region. Uses three pulling chains to remove even the most stubborn drums.

One person can easily set the tool in place and use for tough pulls even where there is little access to insert the jaws. This wheel grabber/ wheel whiz adapter provides the safe way to remove a seized 16.5 brake drum. Kiene brake drum puller adapter.

Capacity, 24in.l x 20 1/2in.w x 58 9/10in.h This tool installs the front and rear crankshaft wear sleeves and seals. Provides up to 7 tons of force to remove frozen brake drums.

On 2/7/2014 at 3:16 am, don coatney said: The drum and the axle have a matched taper. Handles large components such as brake drums, rotors, drive wheels, gears, flywheels, and pulleys.

Two adjusting screws on top and one on bottom, keep the puller. A brand new drum comes at 419 millimeters or. All conmet brake drums are compatible with ball seat systems in dual wheel applications.

Shop for otc heavy duty drum and rotor puller with confidence at autozone.com. The ball seat wheel mounting system is also known as stud piloted, ball seat cap nut (bcn), and double cap nut (dcn) system. It eliminates lip flare on the wear sleeve and installs the seal properly.

20% off orders over $100* + free ground shipping** Semi's have concave wheels, which act as support for the tub. Handles large components such as brake drums, rotors, drive wheels, gears, flywheels, and pulleys one person can easily set the tool in place and use for tough pulls even where there is little access to insert the jaws.

Otc 6979 heavy duty brake drum and rotor puller. In addition to the 5 reach, the jaws are formed with a radius to maximize surface contact for large diameter. This is for your standard american trailer brake drum or drive axle drum.

The puller is required to break the taper bond. This number is often cast on the outside of the drum it's allowed to be 422.1 millimeters or sixteen point six two inches. Heavy duty brake drum and rotor puller.

The magnets were attached with hot glue, but i would. Otc® brake anchor pin and bushing service set (5038) 0. Otc® brake drum and rotor puller (6980) 0.

Sturdy load beam that provides over 12 of spread; Jc whitney brake drum puller eastwood products brake drum puller hook this on the flange of the drum at three equally spaced points, with the center screw pressing on the center of the disk wheel axle flange or inside the center of the wire wheel hub. It comes with two forcing screws for standard and tall brake drums.

Covered by otc's lifetime warranty. Brake drum stud hole size must be confirmed for single wheel applications, however. It is not the brake shoes that require the puller.

It has a usable spread of 17.5 inches and a maximum reach of 12.25 inches. Brake drums have a wear limit which is the maximum inside diameter the brake drum is allowed to be. Tighten the manual screw to pull the tool tight.

All this talk and nobody has mentioned why a puller is required. The otc heavy duty brake drum and rotor puller handles large components such as brake drums, rotors, drive wheels, gears, flywheels and pulleys. Otc® brake drum and rotor puller (6980) 0.

It has a usable spread of 17.5 inches and a maximum reach of 12.25 inches. Shop 22 brake drum puller at northern tool + equipment. Universal brake drum and rotor puller by otc®.

Eliminates the danger of using a large hammer to release a frozen drum. It comes with two forcing screws for standard and tall brake drums. It comes with two forcing screws for standard and tall brake drums.

The brake drum (figure 5). Parts are just part of what we do. I used rare earth neodymium magnets (1/4 x 3/4) to apply a strong bond between the edge of the tub and the wheel.

MK328387 Brake Drum (With images)